User talk:Crushermachine169
Limestone is used in a wide variety of applications, such as direct processing of limestone into stone and firing into quicklime; as a coating material and tile adhesive. Used as a filler for rubber, plastic, paper, toothpaste, cosmetics, etc. However, the use of limestone materials is inseparable from the processing of limestone mills. If limestone is not processed, it can only be filled with simple raw materials. The finer the [url=https://sbm-mill.com/materials/limestone.html]Limestone Mill[/url]'s finer limestone mesh, the wider its use and the higher the value. 1. According to the nature of limestone, formulate the number of fine grinding sands As an important building material, limestone has a long history of mining. Limestone is the main raw material for the manufacture of cement, lime and calcium carbide. It is an indispensable flux limestone in the metallurgical industry. After being ground by a limestone mill, high-quality limestone is widely used in the manufacture of paper, rubber, medicine, cosmetics, feed and other products. In the grinding process by the limestone mill, the number of meshes is determined according to the nature of the limestone. If the limestone has a high hardness and a high density, the first mesh is coarser, but this is not terrible. The limestone can be placed in a limestone mill for fine grinding. Therefore, the grinding number of the limestone mill is related to limestone, adjusting the properties of limestone and improving the fineness of the mesh. 2, according to the demand, adjust the size of the mesh The limestone mill has a reasonable structure, and the fittings cooperate with each other in the work. The system is simple and the layout is compact. It is an advanced and high-end equipment in the milling equipment. Generally, the finished product of the conventional milling equipment has a particle size of 80-325 mesh, and the finished product of the limestone mill has a finer particle size, and there is no requirement for the limestone material. In addition, the limestone mill covers an area of about 50% of the sanding system and can be placed in the open air, thus greatly reducing the investment cost. In addition, the grinding efficiency is high, and the grinding stone powder material is directly crushed on the grinding disc by the grinding roller, and the energy consumption is low. In addition, during the work, the grinding roller is not in direct contact with the grinding disc, and the grinding roller and the lining plate are made of high-quality materials, so the service life is long and the wear is small.
The crusher gives limestone a high finished product
The crusher allows the limestone to be finished. However, the reserves of limestone are in a hurry, and it is only enough for 25 years. Although the prime minister has a large resource title, with the exploitation and waste of resources, many resources have begun to appear in reserve. Limestone is a big example. According to the data, the reserves of medium limestone are only enough for 25 years, while the reserves of coal are enough to mine. As early as 2005, the proven reserves of limestone were 75 billion tons, of which only 39 billion tons were economically exploited (North City Planning and Design Institute, 2007). In 2007, the total production of cement was 1.36 billion tons, and the consumption of limestone was about 1.65 billion tons. The calculation was as long as the consumption was 23.6 years. In order to avoid waste and reuse of resources, it is necessary to consider when crushing and <a href="https://hotelaaryamaan.com/products.html">Stone Crushing Equipment</a>. . Even so, the proven limestone mine is only 45 years and a half. According to industry insiders, limestone is the second largest non-metallic mining product after coal. The reserves are far less than coal. The damage to the surface and landforms is far beyond the coal mining and cannot be restored. In modern industry, limestone is the main raw material for the manufacture of cement, lime and calcium carbide. It is an indispensable flux limestone in the metallurgical industry. After fine grinding, limestone is widely used in the manufacture of paper, rubber, paint, paint, medicine, cosmetics, feed, sealing, bonding, polishing and other products. In combination with the above factors, it is a good choice to use a crusher to crush limestone, which will not waste materials, but also allow the rejected unqualified materials to be reused.
A rough noise solution in the operation of the mill
During the operation of the [url=https://www.sbm-mill.com/products/grinding/lm-mill.html]vertical roller mill[/url], the noise is too high and the speed is uneven, which affects the quality of the product. What should I do in this situation? Most of this phenomenon is caused by mechanical damage or wear and poor lubrication. We first find the fault location according to the generated sound. Remove the protective plate on the back of the mill and notice that the gearbox is beeping. Remove the fixing screws one by one and find that the grease in the gearbox is dry and the gears are bright. The “click” sound of the mill can also be emitted by a DC motor. It may be that the motor bearings are short of oil. If this is the case, remove it and lubricate it and eliminate the sound. Skills can replace high temperatures. First, compress the pressure spring by hand, then place one end of the high temperature belt on the rubber wheel and the other end on the other rubber wheel, set the governor to low speed, start, close to the motion inertia, high temperature belt automatically load. This indicates that the cause of the malfunction is lack of oil. Mix the same type of oil and grease into the gearbox and tighten the screws to recover. When the power is turned on, the "beep" sound disappears, indicating normal. In addition, if the joint of the high temperature belt is slack, severely damaged, the surface is not clean, the surface is dirty, and it will not be synchronized with the traction wheel during operation, and sometimes a "click" sound will be emitted. The solution is to replace the high temperature strip of the same specification. The changes in the times have also made the performance of the mill more outstanding. The former mill achieved the pursuit of automation and found its own direction. The development prospects of the mill will naturally get better and better. Pay attention to your image is a requirement. A good social image makes the development of the mill more pursued. It is not only the profits that are still healthy for you.
